黄色网页在线观看_黄色一级国产精品_高清黄色毛片在线观看_免费黄色A级视频影院

您好,歡迎訪問濟南愛窗加工部 的網站!
客戶服務熱線:13296405222

地址:濟南市天橋區天橋東街后陳家樓31號

聯系我們
濟南愛窗加工部

聯系人:孟經理

聯系電話:13296405222

網址:http://m.luoboyy.com

地址:濟南市天橋區天橋東街后陳家樓31號

當前位置: 首頁 > 新聞資訊 > 公司新聞

電動卷簾門極限調試方法與設置要求

來源:http://m.luoboyy.com/  發布時間:2023-02-16 21:42:55

現如今,越來越多的人會用濟南電動卷簾門來代替商店里的卷簾門。操作起來更加方便,人們?cè)谑褂玫臅r(shí)候也不會有太大的負擔。下面和濟南電動卷簾門安裝維修廠家一起來了解一個問題--電動卷簾門極限調試方法與設置要求。
Nowadays, more and more people will use Jinan electric roller shutter doors to replace the roller shutter doors in stores. It is more convenient to operate, and people will not have too much burden when using it. Now let's work with Jinan electric roller shutter door installation and maintenance manufacturer to understand a problem -- limit commissioning method and setting requirements of electric roller shutter door.
電動卷簾門極限調試方法:
Limit commissioning method of electric roller shutter door:
1.將止動塊上的螺母卡箍轉動到適當?shù)姆较?,以分離螺母塞,或松開止動塊上的夾緊螺釘。
1. Turn the nut clamp on the stopper to the proper direction to separate the nut plug or loosen the clamping screw on the stopper.
2.打開車門正確位置,轉動限位器上的限位螺母,按下車門開啟限位開關上的滾輪。聽到“咔嗒”聲后,將螺母卡入相應的限位螺母或擰緊螺釘。
2. Open the door to the correct position, turn the limit nut on the limit switch, and press the roller on the door opening limit switch. After hearing the "click" sound, clip the nut into the corresponding limit nut or tighten the screw.
3.將車門關閉到適當位置,轉動限位器上的限位螺母,并按下關閉限位開關上的滾輪。聽到“咔嗒”聲后,將螺母卡入相應槽中的限位螺母或擰緊螺釘。
3. Close the door to the proper position, turn the limit nut on the limiter, and press the roller on the closing limit switch. After hearing the "click" sound, clip the nut into the limit nut in the corresponding slot or tighten the screw.
4.如果門的位置不合適,可以將其再次調整到合適的位置。
4. If the position of the door is not appropriate, it can be adjusted to the appropriate position again.
濟南電動卷簾門安裝維修
電動卷簾門的設置要求:
Requirements for setting of electric roller shutter door:
1.當?shù)蹉^滑動到極限位置時,提升操縱桿。當按下限位開關時,電源關閉,只有在箱子關閉時才能降下吊鉤。
1. When the hook slides to the limit position, lift the control lever. When the limit switch is pressed, the power is off, and the hook can only be lowered when the box is closed.
2.在軌道邊緣安裝固定限位擋板(在控制裝置限制的位置)。當塔式起重機運行到此位置時,限位擋板接觸行程開關手柄并斷開電源以控制行程。重合閘時,塔機只能反向運行。
2. Install fixed limit baffle at the edge of the track (at the position limited by the control device). When the tower crane runs to this position, the limit baffle contacts the travel switch handle and disconnects the power supply to control the travel. During reclosing, the tower crane can only operate in reverse direction.
3.在光盤中心安裝一個垂直移動的指針。當振幅改變時,指針指示各種振幅下的額定起重能力。當臂桿移動到上、下限位時,分別按住限位開關,斷開控制電路,變幅電機停止,實現限位功能。
3. Install a vertically moving pointer in the center of the disc. When the amplitude changes, the pointer indicates the rated lifting capacity under various amplitudes. When the boom moves to the upper and lower limit positions, press and hold the limit switch respectively, disconnect the control circuit, and the luffing motor stops to realize the limit function.
以上是電動卷簾門極限調試方法與設置要求的相關內容。希望它能幫助您。如果您想了解更多關于門的知識,歡迎關注我們http://m.luoboyy.com以獲取更多信息。
The above is related to the limit commissioning method and setting requirements of electric roller shutter door. I hope it can help you. If you want to know more about doors, please follow us http://m.luoboyy.com For more information.