濟南卷簾門：調試快速卷簾門的步驟

來源：http://m.luoboyy.com/  發布時間：2024-11-23 15:45:40

　　快速卷簾門控制箱的調試步驟如下：

　　The debugging steps for the fast rolling shutter door control box are as follows:

　　上下限位調試檢測 ：

　　Upper and lower limit debugging and testing:

　　門體靜止狀態下，按下上升按鍵，門體向上運行，待經過緩沖、完全停止后，判斷提升高度是否滿足使用方要求。如不滿足要求，再次進行調試；

　　When the door is in a stationary state, press the up button to move the door upwards. After buffering and complete stop, determine whether the lifting height meets the user's requirements. If the requirements are not met, debug again;

　　事后，按下降按鍵，待門體下落完全停止后，觀察門體末端停留位置是否自然得體。

　　Afterwards, press the descent button and wait for the door to completely stop falling. Observe whether the end of the door stays in a natural and appropriate position.

　　急停按鈕性能檢測 ：

　　Emergency stop button performance testing:

　　門體運行過程中，按下急停按鈕，觀察門體是否立即停止。若依舊正常運行，則需檢查急停按鈕是否失靈或損壞。

　　During the operation of the door, press the emergency stop button and observe whether the door stops immediately. If it still operates normally, it is necessary to check whether the emergency stop button is malfunctioning or damaged.

　　自動開啟功能調試 ：

　　Debugging of automatic activation function:

　　利用車輛、人員移動來模擬實際狀況，觀察門體是否能夠及時開啟，以及是否全角度無死角信號覆蓋。

　　Simulate the actual situation by using vehicle and personnel movements, observe whether the door can be opened in a timely manner, and whether there is no blind spot signal coverage from all angles.

　　紅外防砸性能調試 ：

　　Infrared anti smashing performance debugging:

　　在門體下落過程中，切斷紅外對射系統，看門體是否會及時反彈上升。在測試過程中，應及時聯系工業快速門廠家，要注意自身安全，防止紅外系統失靈造成砸傷情況。

　　Will the door rebound and rise in a timely manner when the infrared radiation system is cut off during the process of the door falling. During the testing process, it is necessary to promptly contact the industrial rapid door manufacturer, pay attention to personal safety, and prevent the infrared system from malfunctioning and causing injury.

　　控制箱電源檢查 ：

　　Control box power supply inspection:

　　檢查控制箱的電源是否正常，確保電源接線正確。

　　Check if the power supply of the control box is normal and ensure that the power wiring is correct.

　　參數設置 ：

　　Parameter settings:

　　根據快速門的要求，設置控制箱的參數，如開門速度、關門速度等。

　　According to the requirements of the fast door, set the parameters of the control box, such as opening speed, closing speed, etc.

　　傳感器連接 ：

　　Sensor connection:

　　連接控制箱與快速門的傳感器，確保傳感器的信號正常。

　　Connect the sensor between the control box and the quick door to ensure that the sensor signal is normal.

　　手動測試 ：

　　Manual testing:

　　通過控制箱的按鈕或遙控器，測試快速門的開關門功能，確保控制箱的調試成功。

　　Test the opening and closing function of the fast door through the buttons or remote control of the control box to ensure successful debugging of the control box.

　　安全性能測試 ：

　　Security performance testing:

　　調試完成后，還需進行安全性能測試，確?？焖匍T的運行安全可靠。

　　After debugging is completed, safety performance testing is also required to ensure the safe and reliable operation of the fast door.

　　限位開關類型設置 ：

　　Limit switch type setting:

　　首次開機時，系統會提示進行限位調試相關設置，需設置限位開關類型，點擊“絕對值式”，然后點擊“確定”按鈕。

　　When starting up for the first time, the system will prompt for limit debugging related settings. You need to set the limit switch type, click "absolute value", and then click the "OK" button.

　　開門按鈕轉向確認 ：

　　Confirm the direction of the door opening button:

　　按控制柜上的“開門”按鈕，確認門體運行方向與實際開門方向是否一致。如果不一致，請點擊“換向”，系統會自動反轉電機的轉向，再次進行確認后點擊“確定”。

　　Press the "Open Door" button on the control cabinet to confirm whether the direction of the door's movement is consistent with the actual opening direction. If there is inconsistency, please click "Reverse Direction", and the system will automatically reverse the direction of the motor. After confirming again, click "OK".

　　上下限位設定 ：

　　Upper and lower limit setting:

　　點動下降，調整門到下限位。按住急停按鈕，按住下降按鈕2~4秒。變頻器出現ATO提示，下限調試完畢。

　　Tap down and adjust the door to the lower limit. Press and hold the emergency stop button, and press and hold the descent button for 2-4 seconds. The frequency converter shows an ATO prompt, and the lower limit debugging is completed.

　　點動上升，調整門到上限位置。按住急停按鈕，按住下降按鈕2~4秒。變頻器出現ATO提示，上限調試完畢。

　　Tap up and adjust the door to the upper limit position. Press and hold the emergency stop button, and press and hold the descent button for 2-4 seconds. The frequency converter shows an ATO prompt, and the upper limit debugging is completed.

　　建議按照上述步驟進行調試，并在測試過程中注意安全，確?？焖倬砗熼T的正常運行和安全性。

　　It is recommended to follow the above steps for debugging and pay attention to safety during the testing process to ensure the normal operation and safety of the fast rolling shutter door.

　　本文由濟南卷簾門為您提供，我們的網站是：http://m.luoboyy.com我們將以全心全意的熱情為您提供服務，歡迎您的訪問！

　　This article is provided by Jinan Rolling Shutter Doors. Our website is: http://m.luoboyy.com We will provide you with wholehearted enthusiasm and welcome your visit!