目前，市面上電動卷簾門的使用量越來越多，傳統的手動卷簾門市場越來越少；使用多了問題也就多了，下面我們就一起看看電動卷簾門出現的四個故障及處理內容吧。

At present, more and more electric roller shutter doors are used in the market, and the traditional manual roller shutter door market is less and less; With more use, there will be more problems. Let's take a look at the four faults of the electric roller shutter door and the handling content.

1、電動機不動或轉速慢

1. The motor does not move or the speed is slow

故障原因：一般是線路斷路、電機燒損、停止按鈕沒復位、限位開關動作、負載較大等引起。

Fault causes: generally, it is caused by open circuit of the line, burning of the motor, failure to reset the stop button, action of the limit switch, large load, etc.

處理方法：檢查線路、并接通；更換燒損電機；更換按鈕或重復按動幾次；撥動限位開關滑塊使它脫離微動開關觸點，并調整微動開關位置；檢查機械部分有無卡阻，若有則卡阻清理障礙物。

Treatment method: check the line and connect it; Replace the burned motor; Change the button or press it repeatedly for several times; Toggle the limit switch slider to separate it from the microswitch contact, and adjust the microswitch position; Check whether the mechanical part is blocked. If so, remove the blockage and clear the obstacles.

2、控制失效

2. Control failure

故障發生的部位及原因：繼電器（接觸器）觸點粘死、行程微動開關失效或觸片變形、滑塊緊定螺釘松、靠板螺絲松使靠板移位，使滑塊或螺母不能隨絲桿轉動而移動、限位器傳動齒輪破損、按鈕上、下鍵卡死。

The position and cause of the fault: the contact of the relay (contactor) is stuck, the travel microswitch is invalid or the contact piece is deformed, the fastening screw of the slider is loose, and the screw of the backup plate is loose, which makes the backup plate shift, so that the slider or nut cannot move with the rotation of the screw rod, the transmission gear of the limiter is damaged, and the upper and lower keys of the button are stuck.

處理方法：更換繼電器（接觸器）；更換微動開關或觸片；緊定滑塊螺釘并使靠板復位；更換限位器傳動齒輪；更換按鈕。

Treatment method: replace the relay (contactor); Replace the microswitch or contact piece; Tighten the slider screw and reset the backup plate; Replace the transmission gear of the stopper; Replace the button.

3、手拉鏈不動

3. Hand zipper does not move

故障原因：環形鏈條堵住十字槽；棘爪無脫離棘輪；壓鏈架卡死。

Fault cause: the ring chain blocks the cross groove; The pawl has no disengagement ratchet; The chain pressing frame is stuck.

處理方法：理順環形鏈條；調整棘爪與壓鏈架相對位置；更換或潤滑銷軸。

Treatment: straighten out the circular chain; Adjust the relative position between the pawl and the chain pressing frame; Replace or lubricate the pin shaft.

4、電機振動或噪聲較大

4. The motor has high vibration or noise

故障原因：剎車盤不平衡或斷裂；剎車盤無緊固；軸承失油或失效；齒輪嚙合不順、失油或磨損嚴重；電機電流聲或振動。

Fault cause: the brake disc is unbalanced or broken; The brake disc is not fastened; Bearing oil loss or failure; Gear meshing is not smooth, oil loss or serious wear; Motor current sound or vibration.

處理方法：濟南電動卷簾門安裝維修人員認為您應該更換剎車盤或重新調整平衡；緊固剎車盤螺母；更換軸承；修配電機軸輸出端齒輪、潤滑或更換；檢查電機，如電機壞損則更換。

Treatment: Jinan electric roller shutter door installation and maintenance personnel think you should replace the brake disc or readjust the balance; Tighten the brake disc nut; Replace the bearing; Repair, lubricate or replace the gear at the output end of the motor shaft; Check the motor and replace it if it is damaged.

電動卷簾門出現的四個故障及處理就是這樣了，出現問題就應該及時處理，防止小問題變成大問題，然后損失更大。更多事項就來我們網站http://m.luoboyy.com咨詢吧。

The four faults of electric roller shutter door and their treatment are like this. If there are problems, they should be handled in time to prevent small problems from turning into big problems, and then the losses will be greater. Come to our website for more information http://m.luoboyy.com Consult.